Liên hệ
Chúng tôi đã sử dụng SUS316L cho vỏ và vật liệu tốt nhất cho tất cả các bộ phận để đạt được độ bền gấp 200 lần so với E3Z (trong dung dịch natri hydroxit 1,5% ở 70°C) để làm cho E3ZM phù hợp với điều kiện làm sạch của máy móc chế biến thực phẩm.
Cấu trúc bảo vệ IP69K* (DIN 40050-9) đầu tiên trên thế giới dành cho cảm biến quang điện kim loại hình vuông. Thích hợp cho các ứng dụng làm sạch phun tia nước áp suất cao, nhiệt độ cao.
* Tham khảo phần chú thích trên Catalog (bảng xếp hạng và thông số kỹ thuật).
Ít vết lõm trong hình dạng có nghĩa là ít bụi và nước có thể tích tụ hơn, làm cho E3ZM hợp vệ sinh hơn. Không có nhãn nào được sử dụng để ngăn chặn các chất lạ làm ô nhiễm các sản phẩm thực phẩm. Mẫu E3ZM và số lô được in bằng cách sử dụng điểm đánh dấu laze.
*Không sử dụng E3ZM trong môi trường có dầu.
Ba mô hình với độ nhạy cố định khác nhau (khoảng cách phát hiện định mức) đã được tạo. Các mẫu này bao gồm phạm vi cảm biến của E3Z-LS61.
Chùm mịn mà không cần gắn khẩu độ bên ngoài. Điều này giúp loại bỏ trục trặc do giọt nước còn sót lại, thậm chí ngay sau khi giặt.
E3ZM có thể được sử dụng trong những môi trường làm sạch khắc nghiệt mà E3Z khó sử dụng. E3ZM đã vượt qua các bài kiểm tra độ bền vật liệu và được chứng nhận bởi Ecolab.
| Sensing method | Appearance | Connection method | Sensing distance | Model | |
|---|---|---|---|---|---|
| NPN output | PNP output | ||||
| Through- beam (Emitter + Receiver) |  | Pre-wired (2 m) | 15 m (Infrared light) | E3ZM-T61 2M Emitter E3ZM-T61-L 2M Receiver E3ZM-T61-D 2M | E3ZM-T81 2M Emitter E3ZM-T81-L 2M Receiver E3ZM-T81-D 2M |
| Connector (M8, 4 pins) | E3ZM-T66 Emitter E3ZM-T66-L Receiver E3ZM-T66-D | E3ZM-T86 Emitter E3ZM-T86-L Receiver E3ZM-T86-D | |||
| Pre-wired (2 m) | 0.8 m (apertures built in) (Infrared light) | E3ZM-T63 2M Emitter E3ZM-T63-L 2M Receiver E3ZM-T63-D 2M | E3ZM-T83 2M Emitter E3ZM-T83-L 2M Receiver E3ZM-T83-D 2M | ||
| Connector (M8, 4 pins) | E3ZM-T68 Emitter E3ZM-T68-L Receiver E3ZM-T68-D | E3ZM-T88 Emitter E3ZM-T88-L Receiver E3ZM-T88-D | |||
| Retro- reflective with MSR function |  *1 | Pre-wired (2 m) | 4 m (100 mm) *2 (Using E39-R1S) (Red light) | E3ZM-R61 2M | E3ZM-R81 2M |
| Connector (M8, 4 pins) | E3ZM-R66 | E3ZM-R86 | |||
| Diffuse- reflective |  | Pre-wired (2 m) | 1 m (Infrared light) | E3ZM-D62 2M | E3ZM-D82 2M |
| Connector (M8, 4 pins) | E3ZM-D67 | E3ZM-D87 | |||
| BGS reflective (fixed distance) |  | Pre-wired (2 m) | 10 to 100 mm (Red light) | E3ZM-LS61H 2M | E3ZM-LS81H 2M |
| Connector (M8, 4 pins) | E3ZM-LS66H | E3ZM-LS86H | |||
| Pre-wired (2 m) | 10 to 150 mm (Red light) | E3ZM-LS62H 2M | E3ZM-LS82H 2M | ||
| Connector (M8, 4 pins) | E3ZM-LS67H | E3ZM-LS87H | |||
| Pre-wired (2 m) | 10 to 200 mm (Red light) | E3ZM-LS64H 2M | E3ZM-LS84H 2M | ||
| Connector (M8, 4 pins) | E3ZM-LS69H | E3ZM-LS89H | |||
(A Reflector is required for each Retro-reflective Sensor: A Reflector is not provided with the Sensor. Be sure to order a Reflector.)
| Name | E3ZM-R Sensing distance * | Model | Quantity | Remarks | |
|---|---|---|---|---|---|
| Rated value | Reference value | ||||
| Reflector | 3 m (100 mm) | — | E39-R1 | 1 | Reflectors are not provided with Retro-reflective models. •The MSR function is enabled. |
| 4 m (100 mm) | — | E39-R1S | 1 | ||
| — | 5 m (100 mm) | E39-R2 | 1 | ||
| — | 2.5 m (100 mm) | E39-R9 | 1 | ||
| — | 3.5 m (100 mm) | E39-R10 | 1 | ||
| Fog Preventive Coating | — | 3 m (100 mm) | E39-R1K | 1 | |
| Small Reflector | — | 1.5 m (50 mm) | E39-R3 | 1 | |
| Tape Reflector | — | 700 mm (150 mm) | E39-RS1 | 1 | |
| — | 1.1 m (150 mm) | E39-RS2 | 1 | ||
| — | 1.4 m (150 mm) | E39-RS3 | 1 | ||
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
| Appearance | Model (Material) | Quantity | Remarks |
|---|---|---|---|
 | E39-L153 (SUS304) *1 | 1 | Mounting Brackets |
 | E39-L104 (SUS304) *1 | 1 | |
 | E39-L43 (SUS304) *2 | 1 | Horizontal Mounting Bracket |
 | E39-L142 (SUS304) *2 | 1 | Horizontal Protective Cover Bracket |
 | E39-L44 (SUS304) | 1 | Rear Mounting Bracket |
 | E39-L98 (SUS304) *2 | 1 | Metal Protective Cover Bracket |
 | E39-L150 (SUS304) | 1 set | (Sensor adjuster) Easily mounted to the aluminum frame rails of conveyors and easily adjusted. For left to right adjustment |
 | E39-L151 (SUS304) | 1 set | |
 | E39-L144 (SUS304) *2 | 1 | Compact Protective Cover Bracket |
(Models for Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
| Size | Cable | Appearance | Cable type | Model | ||
|---|---|---|---|---|---|---|
| M8 (4 pins) *1 | Standard | Straight *2 |  | 2 m | 4-wire | XS3F-M421-402-A |
| 5 m | XS3F-M421-405-A | |||||
| L-shaped *2 *3 |  | 2 m | XS3F-M422-402-A | |||
| 5 m | XS3F-M422-405-A | |||||
| Sensing method | Through-beam | Retro-reflective with MSR function | Diffuse-reflective Models | ||
|---|---|---|---|---|---|
| Model | NPN output | E3ZM-T61 E3ZM-T66 | E3ZM-T63 E3ZM-T68 | E3ZM-R61 E3ZM-R66 | E3ZM-D62 E3ZM-D67 |
| PNP output | E3ZM-T81 E3ZM-T86 | E3ZM-T83 E3ZM-T88 | E3ZM-R81 E3ZM-R86 | E3ZM-D82 E3ZM-D87 | |
| Sensing distance | 15 m | 0.8 m | 4 m [100 mm] (Using E39-R1S) 3 m [100 mm] (Using E39-R1) | 1 m (White paper 300 × 300 mm) | |
| Spot diameter (typical) | — | ||||
| Standard sensing object | Opaque: 12-mm dia. min. | Opaque: 2-mm dia. min. | Opaque: 75-mm dia. min. | — | |
| Differential travel | — | 20% of sensing distance max. | |||
| Black/white error | — | ||||
| Directional angle | Emitter, Receiver: 3° to 15° | Sensor: 3° to 10° Reflector: 30° | — | ||
| Light source (wavelength) | Infrared LED (870 nm) | Red LED (660 nm) | Infrared LED (870 nm) | ||
| Power supply voltage | 10 to 30 VDC, including 10% ripple (p-p) | ||||
| Current consumption | 40 mA max. (Emitter 20 mA max., Receiver 20 mA max.) | 25 mA max. | |||
| Control output | Load power supply voltage: 30 VDC max., Load current: 100 mA max. (Residual voltage: 2 V max.) Open-collector output (NPN/PNP output depending on model) Light-ON/Dark-ON switch selectable | ||||
| Protection circuits | Reversed power supply polarity protection, Output short-circuit protection, and Reversed output polarity protection | Reversed power supply polarity protection, Output short-circuit protection, Mutual interference prevention, and Reversed output polarity protection | |||
| Response time | Operate or reset: 1 ms max. | ||||
| Sensitivity adjustment | One-turn adjuster | ||||
| Ambient illumination (Receiver side) | Incandescent lamp: 3,000 lx max., Sunlight: 10,000 lx max. | ||||
| Ambient temperature range | Operating: -25 to 55°C, Storage: -40 to 70°C (with no icing or condensation) | ||||
| Ambient humidity range | Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) | ||||
| Insulation resistance | 20 MΩ min. at 500 VDC | ||||
| Dielectric strength | 1,000 VAC, 50/60 Hz for 1 min | ||||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | ||||
| Shock resistance | Destruction: 500 m/s2 3 times each in X, Y, and Z directions | ||||
| Degree of protection * | IEC: IP67, DIN 40050-9: IP69K | ||||
| Connection method | Pre-wired cable (standard length: 2 m) M8 4-pin Connector | ||||
| Indicator | Operation indicator (yellow), Stability indicator (green) (Emitter has only power supply indicator (green).) | ||||
| Weight (packed state) | Pre-wired models (with 2-m cable) | Approx. 150 g | Approx. 90 g | ||
| Connector models | Approx. 60 g | Approx. 40 g | |||
| Materials | Case | SUS316L | |||
| Lens | PMMA (polymethylmethacrylate) | ||||
| Display | PEI (Polyetherimide) | ||||
| Sensitivity adjustment and mode selector switch | PEEK (polyetheretherketone) | ||||
| Seals | Fluoro rubber | ||||
| Accessories | Instruction sheet (Note: Reflectors and Mounting Brackets are sold separately.) | ||||
* IP69K Degree of Protection Specifications
IP69K is a protection specification stipulated by DIN 40050 Part 9 of the German standards.
The test item is sprayed with 80°C water from a nozzle of a specified shape at a water pressure of 80 to 100 bar. The amount of water is 14 to 16 liters per minute.
The distance between the test item and the nozzle is 10 to 15 cm. The water is discharged at angles of 0°, 30°, 60°, and 90° from the horizontal plane for 30 seconds at each angle while the test item is rotated horizontally.
| Sensing method | BGS Reflective Models | |||
|---|---|---|---|---|
| Model | NPN output | E3ZM-LS61H E3ZM-LS66H | E3ZM-LS62H E3ZM-LS67H | E3ZM-LS64H E3ZM-LS69H |
| PNP output | E3ZM-LS81H E3ZM-LS86H | E3ZM-LS82H E3ZM-LS87H | E3ZM-LS84H E3ZM-LS89H | |
| Sensing distance | 10 to 100 mm (White paper 100 × 100 mm) | 10 to 150 mm (White paper 100 × 100 mm) | 10 to 200 mm (White paper 100 × 100 mm) | |
| Spot diameter (typical) | 4-mm dia. at sensing distance of 100 mm | 12-mm dia. at sensing distance of 150 mm | 18-mm dia. at sensing distance of 200 mm | |
| Standard sensing object | — | |||
| Differential travel | 3% of sensing distance max. | 15% of sensing distance max. | 20% of sensing distance max. | |
| Black/white error | 5% of sensing distance max. | 10% of sensing distance max. | 20% of sensing distance max. | |
| Directional angle | — | |||
| Light source (wavelength) | Red LED (650 nm) | Red LED (660 nm) | ||
| Power supply voltage | 10 to 30 VDC, including 10% ripple (p-p) | |||
| Current consumption | 25 mA max. | |||
| Control output | Load power supply voltage: 30 VDC max., Load current: 100 mA max. (Residual voltage: 2 V max.) Open-collector output (NPN/PNP output depending on model) Light-ON/Dark-ON cable connection selectable | |||
| Protection circuits | Reversed power supply polarity protection, Output short-circuit protection, Reversed output polarity protection, Mutual interference protection | |||
| Response time | Operate or reset: 1 ms max. | |||
| Sensitivity adjustment | — | |||
| Ambient illumination (Receiver side) | Incandescent lamp: 3,000 lx max., Sunlight: 10,000 lx max. | |||
| Ambient temperature range | Operating: -25 to 55°C, Storage: -40 to 70°C (with no icing or condensation) | |||
| Ambient humidity range | Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) | |||
| Insulation resistance | 20 MΩ min. at 500 VDC | |||
| Dielectric strength | 1,000 VAC, 50/60 Hz for 1 min | |||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | |||
| Shock resistance | Destruction: 500 m/s2 3 times each in X, Y, and Z directions | |||
| Degree of protection * | IEC: IP67, DIN 40050-9: IP69K | |||
| Connection method | Pre-wired cable (standard length: 2 m) M8 4-pin Connector | |||
| Indicator | Operation indicator (yellow), Stability indicator (green) | |||
| Weight (packed state) | Pre-wired models (with 2-m cable) | Approx. 90 g | ||
| Connector models | Approx. 40 g | |||
| Materials | Case | SUS316L | ||
| Lens | PMMA (polymethylmethacrylate) | |||
| Display | PEI (Polyetherimide) | |||
| Seals | Fluoro rubber | |||
| Accessories | Instruction sheet (Note: Mounting Brackets are sold separately.) | |||
* IP69K Degree of Protection Specifications
IP69K is a protection specification stipulated by DIN 40050 Part 9 of the German standards.
The test item is sprayed with 80°C water from a nozzle of a specified shape at a water pressure of 80 to 100 bar. The amount of water is 14 to 16 liters per minute.
The distance between the test item and the nozzle is 10 to 15 cm. The water is discharged at angles of 0°, 30°, 60°, and 90° from the horizontal plane for 30 seconds at each angle while the test item is rotated horizontally.
Đánh giá
Chưa có đánh giá nào.