Cảm biến quang điện Omron E3Z-LS

Liên hệ

Liên hệ :

08 88 44 88 99

Liên hệ :

0978 63 73 78

Liên hệ :

0909 63 73 78

Liên Hệ Tư Vấn

Lưu ý: Quý khách có thể tùy chọn mẫu sản phẩm hoặc liên hệ để được tư vấn

• Mô hình tam giác có thể thiết lập khoảng cách không bị ảnh hưởng bởi màu sắc.

• Cài đặt định vị đơn giản bằng cách sử dụng một điểm LED rõ ràng. (E3Z-LS[]3/LS[]8)

• Phát hiện các bước phút.

Đặc điểm

Sensors

Sensing method	Appearance	Connection method	Sensing distance (white paper)	Model
Sensing method	Appearance	Connection method	Sensing distance (white paper)	NPN output	PNP output
Distance- settable		Pre-wired (2 m)		*E3Z-LS61 2M 1**	*E3Z-LS81 2M 1**
		Connector (M8, 4 pins)		E3Z-LS66	E3Z-LS86
		Pre-wired (2 m)		E3Z-LS63 2M	*E3Z-LS83 2M 2**
		Connector (M8, 4 pins)		E3Z-LS68	E3Z-LS88

*1. M12 Standard Pre-wired Connector Models are also availavble.
When ordering, add “-M1J 0.3M” to the end of the model number (e.g., E3Z-LS61-M1J 0.3M).
The cable is 0.3 m long.
*2. M12 Pre-wired Smartclick Connector Models are also availavble.
When ordering, add “-M1TJ 0.3M” to the end of the model number (e.g., E3Z-LS83-M1TJ 0.3M).
The cable is 0.3 m long.

Accessories (Order Separately)

Sensor I/O Connectors (Sockets on One Cable End)

(Models for Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)

Cable specification	Appearance	Type of cable		Model
Standard M8 cable	Straight *1	2 m	4-wire	XS3F-M421-402-A
	Straight *1	5 m		XS3F-M421-405-A
	L-shaped 1 2	2 m		XS3F-M422-402-A
	L-shaped 1 2	5 m		XS3F-M422-405-A

*1. The connector will not rotate after connecting.
*2. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface.

Thông số kỹ thuật

Sensing method		Distance-settable
Model	NPN output	E3Z-LS61	E3Z-LS66	E3Z-LS63	E3Z-LS68
Model	PNP output	E3Z-LS81	E3Z-LS86	E3Z-LS83	E3Z-LS88
Sensing distance	BGS	White or black paper (100 × 100 mm): 20 mm to set distance		2 mm to set distance (80 mm max.)
Sensing distance	FGS	White paper (100 × 100 mm): Set distance to 200 mm min. Black paper (100 × 100 mm): Set distance to 160 mm min.		—–
Setting range		White paper (100 × 100 mm): 40 to 200 mm Black paper (100 × 100 mm): 40 to 160 mm		White paper (25 × 25 mm): 20 to 80 mm
Differential travel		10% of set distance max. (Refer to Differential Travel vs. Sensing Distance on Data Sheet.)		2% of set distance max.
Reflectivity characteristic (black/white error)		10% of set distance max.		5% of set distance max.
Light source (wavelength)		Red LED (670 nm)		Red LED (650 nm)
Power supply voltage		12 to 24 VDC ±10%, ripple (p-p): 10% max.
Current consumption		30 mA max.
Control output		Load power supply voltage: 26.4 VDC max., Load current: 100 mA max. (residual voltage 1 V max.), Open collector output (NPN or PNP depending on model) Light-ON/Dark-ON switch selectable
BGS/FGS selection		BGS: Open or connected to GND FGS: Connected to Vcc		BGS: Open or connected to GND
Protection circuits		Reversed power supply polarity protection, Output short-circuit protection, Mutual interference prevention
Response time		Operate or reset: 1 ms max.
Distance setting		5-turn endless adjuster
Ambient illumination (Receiver side)		Incandescent lamp: 3,000 lx max.; Sunlight: 10,000 lx max.
Ambient temperature range		Operating: -25 to 55°C, Storage: -40 to 70°C (with no icing or condensation)
Ambient humidity range		Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance		20 MΩ min. at 500 VDC
Dielectric strength		1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance		Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance		Destruction: 500 m/s² for 3 times each in X, Y, and Z directions
Degree of protection		IP67 (IEC 60529)
Connection method		Pre-wired (standard lengths: 2 m and 0.5 m)	Connector (M8, 4 pins)	Pre-wired (standard lengths: 2 m and 0.5 m)	Connector (M8, 4 pins)
Indicators		Operation indicator (orange), Stability indicator (green)
Weight (packed state)		Pre-wired Sensors, 2 m: Approx. 65 g	Approx. 20 g	Pre-wired Sensors, 2 m: Approx. 65 g	Approx. 20 g
Material	Case	PBT (polybutylene terephthalate)
Material	Lens	Modified polyarylate resin
Accessories		Instruction manual (Mounting Brackets must be ordered separately.)