Liên hệ
• Phát hiện kim loại đen.
• Các mô hình với các tần số khác nhau cũng có sẵn để ngăn ngừa nhiễu lẫn nhau.
• Khả năng chống chịu môi trường vượt trội với cáp tiêu chuẩn làm bằng nhựa PVC chống dầu và bề mặt cảm biến làm bằng vật liệu chống dầu cắt gọt.
• Hữu ích để giúp ngăn chặn việc ngắt kết nối. Bộ bảo vệ cáp được cung cấp như một tính năng tiêu chuẩn.
| Appearance | Sensing distance | Connection method | Cable specifi- cations | Polarity | Operation mode | Pin arrangement | Model |
|---|---|---|---|---|---|---|---|
| M8 | 2 mm | Pre-wired Models (2 m) | PUR | Yes | NO | — | E2E-X2D1-U 2M |
| NC | E2E-X2D2-U 2M | ||||||
| M12 Pre-wired Smartclick Connector Models (0.3 m) | PUR | NO | 1: +V, 4: 0 V | E2E-X2D1-M1TGJ-U 0.3M | |||
| NC | 1: +V, 2: 0 V | E2E-X2D2-M1TGJ-U 0.3M | |||||
| M12 | 3 mm | Pre-wired Models (2 m) | PUR | Yes | NO | — | E2E-X3D1-U 2M |
| NC | E2E-X3D2-U 2M | ||||||
| M12 Pre-wired Smartclick Connector Models (0.3 m) | PUR | NO | 1: +V, 4: 0 V | E2E-X3D1-M1TGJ-U 0.3M | |||
| NC | 1: +V, 2: 0 V | E2E-X3D2-M1TGJ-U 0.3M | |||||
| M18 | 7 mm | Pre-wired Models (2 m) | PUR | Yes | NO | — | E2E-X7D1-U 2M |
| NC | E2E-X7D2-U 2M | ||||||
| M12 Pre-wired Smartclick Connector Models (0.3 m) | PUR | NO | 1: +V, 4: 0 V | E2E-X7D1-M1TGJ-U 0.3M | |||
| NC | 1: +V, 2: 0 V | E2E-X7D2-M1TGJ-U 0.3M | |||||
| M30 | 10 mm | Pre-wired Models (2 m) | PUR | Yes | NO | — | E2E-X10D1-U 2M |
| NC | E2E-X10D2-U 2M | ||||||
| M12 Pre-wired Smartclick Connector Models (0.3 m) | PUR | NO | 1: +V, 4: 0 V | E2E-X10D1-M1TGJ-U 0.3M | |||
| NC | 1: +V, 2: 0 V | E2E-X10D2-M1TGJ-U 0.3M |
| Appearance | Sensing distance | Connection method | Cable specifi- cations | Po- lar- ity | Opera- tion mode | Pin arrangement | Model |
|---|---|---|---|---|---|---|---|
| M12 | 3 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | Yes | NO | — | E2E-X3D1S 2M *1 |
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X3D1S-M1 | ||||
| M18 | 7 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | — | E2E-X7D1S 2M *1 | ||
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X7D1S-M1 | ||||
| M30 | 10 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | — | E2E-X10D1S 2M *1 | ||
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X10D1S-M1 |
*1. Models with different frequencies are also available. The model number is E2E-X []D15S (example: E2E-X3D15S 2M).
| Appearance | Sensing distance | Connection method | Cable specifi- cations | Po- lar- ity | Opera- tion mode | Pin arrangement | Model |
|---|---|---|---|---|---|---|---|
| M12 | 8 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | Yes | NO | — | E2E-X8MD1S 2M *1 |
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X8MD1S-M1 | ||||
| M18 | 14 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | — | E2E-X14MD1S 2M *1 | ||
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X14MD1S-M1 | ||||
| M30 | 20 mm | Pre-wired Models (2 m) | PVC (oil- resistant) | — | E2E-X20MD1S 2M *1 | ||
| M12 Connector Models | — | 2: +V and diagnostic output 3: 0 V 4: +V and control output | E2E-X20MD1S-M1 |
*1. Models with different frequencies are also available. The model number is E2E-X[]MD15S (example: E2E-X8MD15S 2M).
• The connector pin assignments of each New E2E DC 2-Wire Model conform to IEC 947-5-2 Table III. (Only DC 2-Wire Models have been changed in comparison to the previous models.)
• The following models with conventional connector pin assignments are available as well. (Only NO Models can be used.) The cable at the right should also be used if the XW3D-P[]55-G11/XW3B-P[]55-G11 Connector Junction Box is already being used.
| Cable length | Model |
|---|---|
| 500 mm | XS2W-D421-BY1 |
| Appearance | Sensing distance | Connection method | Cable specifications | Operation mode | Pin arrangement | Model |
|---|---|---|---|---|---|---|
| M8 | 1.5 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X1R5Y1 2M *2 |
| NC | E2E-X1R5Y2 2M *2 | |||||
| M12 | 2 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X2Y1 2M *1 |
| NC | E2E-X2Y2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X2Y1-M1 | ||
| NC | (1, 2): (AC, AC) | E2E-X2Y2-M1 | ||||
| M18 | 5 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X5Y1 2M *1 |
| NC | E2E-X5Y2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X5Y1-M1 | ||
| NC | (1, 2): (AC, AC) | E2E-X5Y2-M1 | ||||
| M30 | 10 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X10Y1 2M *1 |
| NC | E2E-X10Y2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X10Y1-M1 | ||
| NC | (1, 2): (AC, AC) | E2E-X10Y2-M1 |
*1. Models with different frequencies are also available. The model number is E2E-X[]Y[]5 (example: E2E-X5Y15 2M).
*2. Discontinued at the end of March 2022.
| Appearance | Sensing distance | Connection method | Cable specifications | Operation mode | Pin arrangement | Model |
|---|---|---|---|---|---|---|
| M8 | 2 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X2MY1 2M *2 |
| NC | E2E-X2MY2 2M *2 | |||||
| M12 | 5 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X5MY1 2M *1 |
| NC | E2E-X5MY2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X5MY1 2M | ||
| NC | (1, 2): (AC, AC) | E2E-X5MY2-M1 | ||||
| M18 | 10 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X10MY1 2M *1 |
| NC | E2E-X10MY2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X10MY1-M1 | ||
| NC | (1, 2): (AC, AC) | E2E-X10MY2-M1 | ||||
| M30 | 18 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | E2E-X18MY1 2M *1 |
| NC | E2E-X18MY2 2M | |||||
| M12 Connector Models | — | NO | (3, 4): (AC, AC) | E2E-X18MY1-M1 | ||
| NC | (1, 2): (AC, AC) | E2E-X18MY2-M1 |
*1. Models with different frequencies are also available. The model number is E2E-X[]MY[]5 (example: E2E-X5MY15 2M).
*2. Discontinued at the end of March 2022.
| Appear- ance | Sensing distance | Connection method | Cable specifications | Operation mode | Pin arrange- ment | Applicable connector code | Model |
|---|---|---|---|---|---|---|---|
| M12 | 3 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | NO | — | — | E2E-X3T1 2M |
| M18 | 7 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | — | — | E2E-X7T1 2M | |
| M30 | 10 mm | Pre-wired Models (2 m) | PVC (oil-resistant) | — | — | E2E-X10T1 2M |
Note: There are no unshielded models.
| Appearance | Cable Specification | Type | Cable diameter (mm) | Cable Connection Direction | Cable length (m) | Sensor I/O Connector model number | Applicable Proximity Sensor model number |
|---|---|---|---|---|---|---|---|
| M12 Smartclick Connector  | Oil-resistant polyurethane cable | Sockets on One Cable End | 6 dia. | Straight | 2 m | XS5F-D421-D80-P | E2E-X[]D[]-M1TGJ-U |
| 5 m | XS5F-D421-G80-P | ||||||
| Right-angle | 2 m | XS5F-D422-D80-P | |||||
| 5 m | XS5F-D422-G80-P | ||||||
| Socket and Plug on Cable Ends | Straight (Socket)/ Straight (Plug) | 2 m | XS5W-D421-D81-P | ||||
| 5 m | XS5W-D421-G81-P |
| Appearance | Cable Specification | Type | Cable diameter (mm) | Cable Connection Direction | Cable length (m) | Sensor I/O Connector model number | Applicable Proximity Sensor model number |
|---|---|---|---|---|---|---|---|
| M12 Screw Connector  | Fire-retardant, PVC Robot Cable | Sockets on One Cable End | 6 dia. | Straight | 2 m | XS2F-D421-D80-F | E2E-X[]D[]S-M1 |
| 5 m | XS2F-D421-G80-F | ||||||
| Right-angle | 2 m | XS2F-D422-D80-F | |||||
| 5 m | XS2F-D422-G80-F | ||||||
| Socket and Plug on Cable Ends | Straight (Socket)/ Straight (Plug) | 2 m | XS2W-D421-D81-F | ||||
| 5 m | XS2W-D421-G81-F | ||||||
| Fire-retardant, PVC Robot Cable | Sockets on One Cable End | 6 dia. | Straight | 2 m | XS2F-A421-DB0-F | E2E-X[]Y1-M1 | |
| 5 m | XS2F-A421-GB0-F | ||||||
| Right-angle | 2 m | XS2F-A422-DB0-F | |||||
| 5 m | XS2F-A422-GB0-F | ||||||
| Fire-retardant, PVC Robot Cable | Sockets on One Cable End | 6 dia. | Straight | 2 m | XS2F-A421-D90-F | E2E-X[]Y2-M1 | |
| 5 m | XS2F-A421-G90-F |
Note: For details, refer to Sensor I/O Connectors/Sensor Controllers.
| Size | M8 | M12 | ||
|---|---|---|---|---|
| Shielded | Shielded | Shielded | Unshielded | |
| Model | E2E-X2D[] | E2E-X3D[] | E2E-X8MD[] | |
| Sensing distance | 2 mm ±10% | 3 mm ±10% | 8 mm ±10% | |
| Set distance *1 | 0 to 1.6 mm | 0 to 2.4 mm | 0 to 6.4 mm | |
| Differential travel | 15% max. of sensing distance | 10% max. of sensing distance | ||
| Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Data Sheet.) | |||
| Standard sensing object | Iron, 8 × 8 × 1 mm | Iron, 12 × 12 × 1 mm | Iron, 30 × 30 × 1 mm | |
| Response frequency *2 | 1.5 kHz | 0.8 kHz | ||
| Power supply voltage (operating voltage range) | 12 to 24 VDC, ripple (p-p): 10% max. (10 to 30 VDC) | |||
| Leakage current | 0.8 mA max. | |||
| Control output | Load current | 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models | ||
| Residual voltage | 3 V max. (Load current: 100 mA, Cable length: 2 m) | |||
| Indicators | D1 Models: Operation indicator (red) and setting indicator (green) D2 Models: Operation indicator (red) | |||
| Operation mode (with sensing object approaching) | D1 Models: NO D2 Models: NC Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details. | |||
| Diagnostic output delay | 0.3 to 1 s | |||
| Protection circuits | Surge suppressor, Load short-circuit protection (for control and diagnostic output) | |||
| Ambient temperature range | Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation) | |||
| Ambient humidity range | Operating/storage: 35% to 95% (with no condensation) | |||
| Temperature influence | ±15% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ||
| Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | |||
| Insulation resistance | 50 MΩ min. (at 500 VDC) between current-carrying parts and case | |||
| Dielectric strength | 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case | |||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | |||
| Shock resistance | Destruction: 500 m/s2 10 times each in X, Y, and Z directions | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | ||
| Degree of protection | Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67 | |||
| Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired Connector Models (Standard cable length: 0.3 m) | |||
| Weight (packed state) | Pre-wired Models | Approx. 60 g | Approx. 70 g | |
| Pre-wired Connector Models | — | Approx. 40 g (Shielded Models only) | ||
| Connector Models | Approx. 15 g | Approx. 25 g | ||
| Materi- als | Case | Stainless steel (SUS303) | Nickel-plated brass | |
| Sensing surface | PBT | |||
| Clamping nuts | Nickel-plated brass | |||
| Toothed washer | Zinc-plated iron | |||
| Accessories | Instruction manual | |||
| Size | M18 | M30 | |||
|---|---|---|---|---|---|
| Shielded | Shielded | Unshielded | Shielded | Unshielded | |
| Model | E2E-X7D[] | E2E-X14MD[] | E2E-X10D[] | E2E-X20MD[] | |
| Sensing distance | 7 mm ±10% | 14 mm ±10% | 10 mm ±10% | 20 mm ±10% | |
| Set distance *1 | 0 to 5.6 mm | 0 to 11.2 mm | 0 to 8 mm | 0 to 16 mm | |
| Differential travel | 10% max. of sensing distance | ||||
| Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Data Sheet.) | ||||
| Standard sensing object | Iron, 18 × 18 × 1 mm | Iron, 30 × 30 × 1 mm | Iron, 54 × 54 × 1 mm | ||
| Response frequency *2 | 0.5 kHz | 0.4 kHz | 0.1 kHz | ||
| Power supply voltage (operating voltage range) | 12 to 24 VDC, ripple (p-p): 10% max. (10 to 30 VDC) | ||||
| Leakage current | 0.8 mA max. | ||||
| Control output | Load current | 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models | |||
| Residual voltage | 3 V max. (Load current: 100 mA, Cable length: 2 m) | ||||
| Indicators | D1 Models: Operation indicator (red) and setting indicator (green) D2 Models: Operation indicator (red) | ||||
| Operation mode (with sensing object approaching) | D1 Models: NO D2 Models: NC Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details. | ||||
| Diagnostic output delay | 0.3 to 1 s | ||||
| Protection circuits | Surge suppressor, Load short-circuit protection (for control and diagnostic output) | ||||
| Ambient temperature range | Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation) | ||||
| Ambient humidity range | Operating/storage: 35% to 95% (with no condensation) | ||||
| Temperature influence | ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ||||
| Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | ||||
| Insulation resistance | 50 MΩ min. (at 500 VDC) between current-carrying parts and case | ||||
| Dielectric strength | 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case | ||||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | ||||
| Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | ||||
| Degree of protection | Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67 | ||||
| Connection method | Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired Connector Models (Standard cable length: 0.3 m) | ||||
| Weight (packed state) | Pre-wired Models | Approx. 130 g | Approx. 175 g | ||
| Pre-wired Connector Models | — | — | |||
| Connector Models | Approx. 40 g | Approx. 90 g | |||
| Materi- als | Case | Nickel-plated brass | |||
| Sensing surface | PBT | ||||
| Clamping nuts | Nickel-plated brass | ||||
| Toothed washer | Zinc-plated iron | ||||
| Accessories | Instruction manual | ||||
*1. Use the E2E within the range in which the setting indicator (green LED) is ON (except D2 Models).
*2. The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object,
and a set distance of half the sensing distance.
| Size | M8 | M12 | |||
|---|---|---|---|---|---|
| Shielded | Shielded | Unshielded | Shielded | Unshielded | |
| Model | E2E-X1R5Y[] | E2E-X2MY[] | E2E-X2Y[] | E2E-X5MY[] | |
| Sensing distance | 1.5 mm ±10% | 2 mm ±10% | 5 mm ±10% | ||
| Set distance | 0 to 1.2 mm | 0 to 1.6 mm | 0 to 4 mm | ||
| Differential travel | 10% max. of sensing distance | ||||
| Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Data Sheet.) | ||||
| Standard sensing object | Iron, 8 × 8 × 1 mm | Iron, 12 × 12 × 1 mm | Iron, 15 × 15 × 1 mm | ||
| Response frequency | 25 Hz | ||||
| Power supply voltage (operating voltage range) *1 | 24 to 240 VAC (20 to 264 VAC), 50/60 Hz | ||||
| Leakage current | 1.7 mA max. | ||||
| Control output | Load current *2 | 5 to 100 mA | 5 to 200 mA | ||
| Residual voltage | Refer to Engineering Data on Data Sheet. | ||||
| Indicators | Operation indicator (red) | ||||
| Operation mode (with sensing object approaching) | Y1 Models: NO Y2 Models: NC Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details. | ||||
| Protection circuits | Surge suppressor | ||||
| Ambient temperature range *1 *2 | Operating/Storage: -25 to 70°C (with no icing or condensation) | Operating/Storage: -40 to 85°C (with no icing or condensation) | |||
| Ambient humidity range | Operating/storage: 35% to 95% (with no condensation) | ||||
| Temperature influence | ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C, ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | |||
| Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | ||||
| Insulation resistance | 50 MΩ min. (at 500 VDC) between current-carrying parts and case | ||||
| Dielectric strength | 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying parts and case | ||||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | ||||
| Shock resistance | Destruction: 500 m/s2 10 times each in X, Y, and Z directions | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | |||
| Degree of protection | Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67 | ||||
| Connection method | Pre-wired Models (Standard cable length: 2 m) and Connector Models | ||||
| Weight (packed state) | Pre-wired Models Model | Approx. 60 g | Approx. 70 g | ||
| Connector Models | Approx. 15 g | Approx. 25 g | |||
| Materials | Case | Stainless steel (SUS303) | Nickel-plated brass | ||
| Sensing surface | PBT | ||||
| Clamping nuts | Nickel-plated brass | ||||
| Toothed washer | Zinc-plated iron | ||||
| Accessories | Instruction manual | ||||
| Size | M18 | M30 | |||
|---|---|---|---|---|---|
| Shielded | Shielded | Unshielded | Shielded | Unshielded | |
| Model | E2E-X5Y[] | E2E-X10MY[] | E2E-X10Y[] | E2E-X18MY[] | |
| Sensing distance | 5 mm ±10% | 10 mm ±10% | 18 mm ±10% | ||
| Set distance | 0 to 4 mm | 0 to 8 mm | 0 to 14 mm | ||
| Differential travel | 10% max. of sensing distance | ||||
| Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Data Sheet.) | ||||
| Standard sensing object | Iron, 18 × 18 × 1 mm | Iron, 30 × 30 × 1 mm | Iron, 54 × 54 × 1 mm | ||
| Response frequency | 25 Hz | ||||
| Power supply voltage (operating voltage range) *1 | 24 to 240 VAC (20 to 264 VAC), 50/60 Hz | ||||
| Leakage current | 1.7 mA max. | ||||
| Control output | Load current *2 | 5 to 300 mA | |||
| Residual voltage | Refer to Engineering Data on Data Sheet. | ||||
| Indicators | Operation indicator (red) | ||||
| Operation mode (with sensing object approaching) | Y1 Models: NO Y2 Models: NC Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details. | ||||
| Protection circuits | Surge suppressor | ||||
| Ambient temperature range *1 *2 | Operating/Storage: -40 to 85°C (with no icing or condensation) | ||||
| Ambient humidity range | Operating/storage: 35% to 95% (with no condensation) | ||||
| Temperature influence | ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C, ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | ||||
| Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | ||||
| Insulation resistance | 50 MΩ min. (at 500 VDC) between current-carrying parts and case | ||||
| Dielectric strength | 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying parts and case | ||||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | ||||
| Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | ||||
| Degree of protection | Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant Connector Models: IEC 60529 IP67 | ||||
| Connection method | Pre-wired Models (Standard cable length: 2 m) and Connector Models | ||||
| Weight (packed state) | Pre-wired Models Model | Approx. 130 g | Approx. 175 g | ||
| Connector Models | Approx. 40 g | Approx. 90 g | |||
| Materials | Case | Stainless steel (SUS303) | Nickel-plated brass | ||
| Sensing surface | PBT | ||||
| Clamping nuts | Nickel-plated brass | ||||
| Toothed washer | Zinc-plated iron | ||||
| Accessories | Instruction manual | ||||
*1. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is at
least −25°C.
*2. When using an M18 or M30 Connector Model at an ambient temperature between 70 and 85°C, make sure that the
Sensor has a control output (load current) of 5 to 200 mA max.
| Size | M12 | M18 | M30 | |
|---|---|---|---|---|
| Shielded | Shielded | |||
| Model | E2E-X3T1 | E2E-X7T1 | E2E-X10T1 | |
| Sensing distance | 3 mm ±10% | 7 mm ±10% | 10 mm ±10% | |
| Set distance | 0 to 2.4 mm | 0 to 5.6 mm | 0 to 8 mm | |
| Differential travel | 10% max. of sensing distance | |||
| Detectable object | Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on Data Sheet.) | |||
| Standard sensing object | Iron, 12 × 12 × 1 mm | Iron, 18 × 18 × 1 mm | Iron, 30 × 30 × 1 mm | |
| Response frequency *1 | DC | 1 kHz | 0.5 kHz | 0.4 kHz |
| AC | 25 Hz | |||
| Power supply voltage (operating voltage range) *2 | 24 to 240 VDC (20 to 264 VDC) 48 to 240 VAC (40 to 264 VAC) | |||
| Leakage current | DC: 1 mA max. AC: 2 mA max. | |||
| Control output | Load current | 5 to 100 mA | ||
| Residual voltage | DC: 6 V max. (Load current: 100 mA, Cable length: 2 m) AC: 10 V max. (Load current: 5 mA, Cable length: 2 m) | |||
| Indicators | Operation indicator (red), Setting indicator (green) | |||
| Operation mode (with sensing object approaching) | NO (Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.) | |||
| Protection circuits | Load short-circuit protection (20 to 40 VDC only), Surge suppressor | |||
| Ambient temperature range | Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation) | |||
| Ambient humidity range | Operating/Storage: 35% to 95% (with no condensation) | |||
| Temperature influence | ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C | |||
| Voltage influence | ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range | |||
| Insulation resistance | 50 MΩ min. (at 500 VDC) between current-carrying parts and case | |||
| Dielectric strength | 4,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case | |||
| Vibration resistance | Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions | |||
| Shock resistance | Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions | |||
| Degree of protection | IEC 60529 IP67, in-house standards: oil-resistant | |||
| Connection method | Pre-wired Models (Standard cable length: 2 m) | |||
| Weight (packed state) | Approx. 80 g | Approx. 140 g | Approx. 190 g | |
| Materials | Case | Nickel-plated brass | ||
| Sensing surface | PBT | |||
| Clamping nuts | Nickel-plated brass | |||
| Toothed washer | Zinc-plated iron | |||
| Accessories | Instruction manual | |||
*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a
distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. Power Supply Voltage Waveform:
Use a sine wave for the power supply. Using a rectangular AC power supply may result in faulty reset.
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
E2E-X2D[]-U
E2E-X3D[]-U
E2E-X7D[]-U
E2E-X10D[]-U
E2E-X2D[]-M1TGJ-U
E2E-X3D[]-M1TGJ-U
E2E-X7D[]-M1TGJ-U
E2E-X10D[]-M1TGJ-U
E2E-X3D1S
E2E-X7D1S
E2E-X10D1S
E2E-X8MD1S
E2E-X14MD1S
E2E-X20MD1S
E2E-X3D1S-M1
E2E-X7D1S-M1
E2E-X10D1S-M1
E2E-X8MD1S-M1
E2E-X14MD1S-M1
E2E-X20MD1S-M1
E2E-X1R5Y[]
E2E-X2Y[]
E2E-X5Y[]
E2E-X10Y[]
E2E-X2MY[]
E2E-X5MY[]
E2E-X10MY[]
E2E-X18MY[]
E2E-X2Y[]-M1
E2E-X5Y[]-M1
E2E-X10Y[]-M1
E2E-X5MY[]-M1
E2E-X10MY[]-M1
E2E-X18MY[]-M1
E2E-X3T1
E2E-X7T1
E2E-X10T1
Đánh giá
Chưa có đánh giá nào.