Chưa có sản phẩm trong giỏ hàng.
Consult with your OMRON representative when ordering any models that are not listed in this table.
Công tắc hành trình Omron D4B-4117N
Liên hệ
Liên hệ :
08 88 44 88 99
Liên hệ :
0978 63 73 78
Liên hệ :
0909 63 73 78
Liên Hệ Tư Vấn
Lưu ý: Quý khách có thể tùy chọn mẫu sản phẩm hoặc liên hệ để được tư vấn
Công tắc giới hạn an toàn chắc chắn với vỏ kim loại. Tiếp điểm tác động chậm và tác động nhanh với chứng nhận vận hành mở trực tiếp đã được chứng nhận.
• Cơ chế mở trực tiếp (chỉ các tiếp điểm NC) được thêm vào để cho phép mở các tiếp điểm khi xảy ra lỗi, chẳng hạn như các tiếp điểm bị chảy.
• Đảm bảo an toàn khi cài đặt cần gạt bằng cách sử dụng cơ chế ăn khớp bánh răng giữa tấm chỉ báo vị trí vận hành và cần gạt.
• Được trang bị cơ chế chỉ báo vùng vận hành áp dụng, cũng như chuyển đổi bằng nút nhấn để điều khiển chuyển động trái và phải.
• Tăng cường cấu trúc đầu bịt kín để cải thiện đặc tính của phớt (TÜV: IEC IP67, UL: NEMA 3, 4, 4X, 6P và 13).
• Dải nhiệt độ hoạt động tiêu chuẩn rộng: –40 đến 80°C (loại tiêu chuẩn).
• Chứng nhận tiêu chuẩn: UL, CSA, EN (TÜV), CCC.
Đặc điểm
Set Model Numbers
Safety Limit Switches (with Direct Opening Mechanism)
| Actuator | Conduit openings | 1NC/1NO (Snap-action) | 1NC/1NO (Slow-action) | 2NC (Slow-action) | ||||
|---|---|---|---|---|---|---|---|---|
| Model | Direct opening | Model | Direct opening | Model | Direct opening | |||
| Roller lever (resin roller) |  | G1/2 (PF1/2) | D4B-2111N |  | D4B-2511N | | D4B-2A11N | |
| M20 | D4B-4111N | D4B-4511N | D4B-4A11N | |||||
| Roller lever (stainless steel roller) | | G1/2 (PF1/2) | D4B-2115N | | D4B-2515N | | D4B-2A15N | |
| M20 | D4B-4115N | D4B-4515N | D4B-4A15N | |||||
| Plunger |  | G1/2 (PF1/2) | D4B-2170N | | D4B-2570N | | D4B-2A70N | |
| M20 | D4B-4170N | D4B-4570N | D4B-4A70N | |||||
| Roller plunger |  | G1/2 (PF1/2) | D4B-2171N | | D4B-2571N | | D4B-2A71N | |
| M20 | D4B-4171N | D4B-4571N | D4B-4A71N | |||||
General-purpose Limit Switches
| Actuator | Conduit openings | 1NC/1NO (Snap-action) | 1NC/1NO (Slow-action) | 2NC (Slow-action) | ||||
|---|---|---|---|---|---|---|---|---|
| Model | Direct opening | Model | Direct opening | Model | Direct opening | |||
| Adjustable roller lever |  | G1/2 (PF1/2) | D4B-2116N | — | D4B-2516N | — | D4B-2A16N | — |
| M20 | D4B-4116N | D4B-4516N | D4B-4A16N | |||||
| Adjustable rod lever |  | G1/2 (PF1/2) | D4B-2117N | — | D4B-2517N | — | D4B-2A17N | — |
| M20 | D4B-4117N | D4B-4517N | D4B-4A17N | |||||
Note: Consult your OMRON representative for products.
Thông số kỹ thuật
Standards and EC Directives
Conforms to the following EC Directives:
• Machinery Directive
• Low Voltage Directive
• EN50041
• EN60204-1
• EN ISO 14119
Certified Standards
Snap-action Models
| Certification body | Standard | File No. |
|---|---|---|
| TÜV Rheinland | EN60947-5-1 (certified direct opening mechanism) GS-ET-15 | Consult your OMRON representative for details. |
| EN60947-5-1 (uncertified direct opening mechanism) | J50005477 * | |
| UL | UL508 | E76675 |
| CSA | C22.2 No. 14 | LR45746 |
| CQC (CCC) | GB/T14048.5 | Contact your OMRON representative for details. |
* Adjustable roller lever, adjustable rod lever only.
Slow-action Mode
| Certification body | Standard | File No. |
|---|---|---|
| TÜV Rheinland | EN60947-5-1 (certified direct opening mechanism) GS-ET-15 | Consult your OMRON representative for details. |
| EN60947-5-1 (uncertified direct opening mechanism) | J50005477 * | |
| UL | UL508 | E76675 |
| CSA | C22.2 No. 14 | LR45746 |
| CQC (CCC) | GB/T14048.5 | Contact your OMRON representative for details. |
* Adjustable roller lever, adjustable rod lever only.
Certified Standard Ratings
TÜV (EN60947-5-1), CCC (GB/T14048.5)
| Utilization category | AC-15 |
|---|---|
| Rated operating current (Ie) | 2 A |
| Rated operating voltage (Ue) | 400 V |
Note: As protection against short-circuiting, use either a gI-type or gG-type 10 A fuse that conforms to IEC60269.
UL/CSA: (UL508, CSA C22.2 No. 14)
A600
| Rated voltage | Carry current | Current (A) | Volt-amperes (VA) | ||
|---|---|---|---|---|---|
| Make | Break | Make | Break | ||
| 120 VAC 240 VAC 480 VAC 600 VAC | 10 A | 60 30 15 12 | 6 3 1.5 1.2 | 7,200 | 720 |
Ratings
| Rated voltage (V) | Non-inductive load (A) | Inductive load (A) | ||||||
|---|---|---|---|---|---|---|---|---|
| Resistive load | Lamp load | Inductive load | Motor load | |||||
| NC | NO | NC | NO | NC | NO | NC | NO | |
| 125 VAC 250 400 | 10 10 10 | 3 2 1.5 | 1.5 1 0.8 | 10 10 3 | 5 3 1.5 | 2.5 1.5 0.8 | ||
| 8 VDC 14 30 125 250 | 10 10 6 0.8 0.4 | 6 6 4 0.2 0.1 | 3 3 3 0.2 0.1 | 10 10 6 0.8 0.4 | 6 6 4 0.2 0.1 | |||
Note: 1. The above values are continuous currents.
2. Inductive loads have a power factor of 0.4 or higher (AC) or a time constant of 7 ms or lower (DC).
3. Lamp loads have a inrush current of 10 times the normal current.
4. Motor loads have a inrush current of 6 times the normal current.
| Inrush current | 30 A max. |
|---|
Characteristics
| Degree of protection *1 | IP67 (EN60947-5-1) | |
|---|---|---|
| Durability *2 | Mechanical | 30,000,000 operations min. (snap-action) 10,000,000 operations min. (slow-action) |
| Electrical | 500,000 operations min. (10 A resistive load at 250 VAC) | |
| Operating speed | 1 mm/s to 0.5 m/s | |
| Operating frequency | Mechanical | 120 operations/minute |
| Electrical | 30 operations/minute | |
| Contact resistance | 25 mΩ max. | |
| Minimum applicable load *3 | 180 mA resistive load at 5 VAC (N-level reference value) | |
| Rated insulation voltage (Ui) | 600 V (EN60947-5-1) | |
| Rated frequency | 50/60 Hz | |
| Protection against electric shock | Class I (with ground terminal) | |
| Pollution degree (operating environment) | 3 (EN60947-5-1) | |
| Impulse withstand voltage (EN60947-5-1) | Between terminals of same polarity | 2.5 kV (snap-action)/4 kV (slow-action) |
| Between terminals of different polarity | 4 kV (slow-action) | |
| Between each terminal and ground | 4 kV | |
| Insulation resistance | 100 MΩ min. (at 500 VDC) between terminals of the same polarity and between each terminal and non-current-carrying part | |
| Contact gap | 2 × 2 mm min. (slow-action) 2 × 0.5 mm min. (snap-action) | |
| Vibration resistance | Malfunction | 10 to 55 Hz, 0.75 mm single amplitude |
| Shock resistance | Destruction | 1,000 m/s2 min. |
| Malfunction | 300 m/s2 min. | |
| Conditional short-circuit current | 100 A (EN60947-5-1) | |
| Conventional enclosed thermal current (Ithe) | 20 A (EN60947-5-1) | |
| Ambient operating temperature | -40 to 80°C (with no icing) | |
| Ambient operating humidity | 95% max. | |
| Weight | Approx. 250 g | |
Note: 1. The above values are initial values.
2. The above values may vary depending on the model. Consult your OMRON sales representative for details.
*1. The degree of protection is tested using the method specified by the standard (EN60947-5-1). Confirm that sealing
properties are sufficient for the operating conditions and environment beforehand.
*2. The durability is for an ambient temperature of 5 to 35°C and ambient humidity of 40% to 70%. For further
conditions, consult your OMRON sales representative.
*3. The above values may vary depending on switching frequency, environmental condition, and relativity level, consult
your OMRON sales representative.
Kích thước
(Unit: mm)
Note: Omitted dimensions are the same as those for the Roller Lever Type Models
D4B-2[][][]N have a G1/2 conduit opening.
D4B-4[][][]N have a M20 conduit opening.
D4B-2[][][]N have a G1/2 conduit opening.
D4B-4[][][]N have a M20 conduit opening.
Switches
Roller Lever
D4B-[][]11N
![D4B-[]N Dimensions 3](https://www.ia.omron.com/Images/392_dm_113-112046.gif)
Roller Lever (Stainless Steel Roller)
D4B-[][]15N
![D4B-[]N Dimensions 4](https://www.ia.omron.com/Images/392_dm_213-112048.gif)
Adjustable Roller Lever *2
D4B-[][]16N
![D4B-[]N Dimensions 5](https://www.ia.omron.com/Images/392_dm_313-112050.gif)
Adjustable Rod Lever *2
D4B-[][]17N
![D4B-[]N Dimensions 6](https://www.ia.omron.com/Images/392_dm_413-112052.gif)
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
*1. The lever can be set to any desired position by turning the operating position indicator.
*2. In terms of construction, the Switch is a General-purpose Limit Switch rather than a Safety Limit Switch.
![D4B-[]N Dimensions 8](https://www.ia.omron.com/Images/392_dm_513-112054.gif)
Note: Variation occurs in the simultaneity of contact opening/closing operations of 2NC contacts. Check contact operation.
*1. The operating characteristics of these Switches were measured with the roller level set at 31.5 mm.
*2. The operating characteristics of these Switches were measured with the rod level set at 140 mm.
*3. The operating characteristics are the same for the left and the right.
*4. Only for slow-action models.
*5. Only for snap-action models.
*6. Reference values.
*7. Must be provided to ensure safe operation.
*1. The operating characteristics of these Switches were measured with the roller level set at 31.5 mm.
*2. The operating characteristics of these Switches were measured with the rod level set at 140 mm.
*3. The operating characteristics are the same for the left and the right.
*4. Only for slow-action models.
*5. Only for snap-action models.
*6. Reference values.
*7. Must be provided to ensure safe operation.
Plunger
D4B-[][]70N
![D4B-[]N Dimensions 9](https://www.ia.omron.com/Images/392_dm_613-112056.gif)
Roller Plunger
D4B-[][]71N
![D4B-[]N Dimensions 10](https://www.ia.omron.com/Images/392_dm_713-112058.gif)
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
![D4B-[]N Dimensions 12](https://www.ia.omron.com/Images/392_dm_813-112060.gif)
Note: Variation occurs in the simultaneity of contact opening/closing operations of 2NC contacts. Check contact operation.
*1. Only for slow-action models.
*2. Only for snap-action models.
*3. Reference values.
*4. Must be provided to ensure safe operation.
MODEL
| STT | Chi tiết | Tiêu đề | Tải xuống |
| 1 | DANH SÁCH MODEL | D4B | Item list of D4B |
TÀI LIỆU
| STT | Chi tiết | Tiêu đề | Tải xuống |
| 1 | TÀI LIỆU | D4B |  |
Hãy là người đầu tiên nhận xét “Công tắc hành trình Omron D4B-4117N”
SẢN PHẨM LIÊN QUAN
Liên hệ
Liên hệ
Liên hệ
Đánh giá
Chưa có đánh giá nào.