Công tắc hành trình Omron Z-5GW2255-M19LE 0.6M

Liên hệ

Liên hệ :

08 88 44 88 99

Liên hệ :

0978 63 73 78

Liên hệ :

0909 63 73 78

Liên Hệ Tư Vấn

Lưu ý: Quý khách có thể tùy chọn mẫu sản phẩm hoặc liên hệ để được tư vấn

Công tắc hành trình loại thông dụng, phổ biến 1 tiếp điểm 2 trạng thái NO/NC

SPDT (1NO-1NC).

Chính xác, nhiều kiểu dáng tác động, cho các ứng dụng khác nhau.

Khả năng chụi tải tiếp điểm cao 15A, với độ chính xác lập lại cao.

Kiểu tác động: Cần gạt lều ngắn

Tần số hoạt động: + Cơ: 240 lần/Max + Điện: 20 lần/Max

Kiểu đấu nối: Terminal

Nhiệt độ môi trường: -25-80°C

Cấp bảo vệ: : IP65

Đặc điểm

Z4D-F

Output	Model
Analog	Z4D-F04A
ON/OFF	Z4D-F04D

Accessories (Attached)

Item	Z4D-F04A	Z4D-F04D
Mounting bracket	1 pc.	1 pc.
Mounting screws (M3 x 2)	2 pcs.	2 pcs.
Connector with 1-m cord	1 pc.	1 pc.
Screwdriver	—	1 pc.
Operation Manual	1 copy	1 copy

Accessories (Optional)

Appearance	Name	Model number	Remarks
	Mounting Bracket	E39-L69	The following products are provided with the Sensors. The products can also be purchased separately.
	Connector with 1-m Cord	EE-1010D

Thông số kỹ thuật

Ratings/Characteristics

Item	Z4D-F04A	Z4D-F04D
Supply voltage	12 to 24 VDC±10%, ripple voltage (p-p): 10 mV max.
Current consumption	35 mA max.
*Sensing range 1**	4±1.25 mm
Light source	Red LED with a wavelength of 700 nm
*Spot diameter 2**	1.5 x 1.5 mm max. (at the sensing range of 4 mm)
*Connection impedance 3**	200 kΩ min.	—
*Resolution 4**	5 μm max.	—
*Hysteresis 1**	—	40 μm
*Linearity 5**	±1% FS	—
*Analog output 1**	1 to 5 V (1.6 V/mm±10%)	—
Control output	—	NPN open collector, 12 to 24 VDC, 50 mA max.
Residual output voltage	—	1 V max.
*Response time 6**	5 ms max.	1.5 ms max.
*Temperature influence 7**	0.15% FS/°C	—
Indicator	PWR indicator (green): Lit when power is supplied ALM indicator (red): Lit when illumination is insufficient.	STB indicator (green): Lit when illumination is sufficient. OPE indicator (orange): Lit when output is ON.
Ambient temperature	Operating: -10°C to 55°C (with no icing) Storage: -15°C to 60°C (with no icing)
Ambient humidity	Operating: 35% to 85% (with no icing)
Ambient illumination	Operating: 3000 lx max. (incandescent lamp), 10,000 lx max. (sunlight)
Enclosure rating	IP50 (IEC standard)
Vibration resistance	Destruction: 10 to 500 Hz (1-mm max. single amplitude) for 11 min for 3 times each in X, Y, and Z directions.
Shock resistance	Destruction: 500 m/s² for 3 times each in X, Y, and Z directions (total of 18 times)
Dielectric strength	1,000 VAC for 1 min between current carry parts and case.
Tightening torque	0.6 Nm max.
Material	ABS (Polycarbonate for the sensing part)
Weight	Approx. 10 g (without connector cable)
Insulation resistance	20 MΩ min. (at 500 VDC)
Cable length	1 m

*1. The values are for N8.5 Munsell paper.
*2. The spot diameter is defined by 1/e² of the Sensor’s laser beam center. Although a sub-beam may be observed
around the main beam, this does not mean that the product is defective.
*3. Refers to input impedance of a device to be connected
*4. Resolution (Z4D-F04A)
The resolution is the peak-to-peak displacement conversion value of the analog displacement output (Conditions:
N8.5 Munsell mat paper at the center of measurement point with a power ripple noise of 10 mV (p-p) max.)

*5. The value is the peak-to-peak error rate of a displacement output voltage line with N8.5 Munsell mat paper. The
value varies with the sensing object.
*6. Response Time (Z4D-F04A)
The response time of the Sensor (Z4D-F04A) is the time required for the analog displacement output to increase
from 10% to 90% of the full value (at the rise time) or decrease from 90% to 10% of the full value (at the fall time).